Residential
Powered Anode Rod
How it works
Powered anode rods are a new generation of anode rod that is much more effective than existing sacrificial magnesium anode rods. The Corro-Protec Powered Anode Rod is a long-term protection solution that is disrupting the water heater and water treatment industries.
Our system uses a titanium anode and a current rectifier. When the power supply is connected to the nearest outlet, the powered anode rod supplies a small amount of current into the water heater. This current completely stops the loss of energy from all metals inside the water heater, effectively stopping and preventing corrosion.
The same current is used to neutralize bacteria causing smelly water and reduces limescale accumulation as you can read in the following advantages section.
One last thing, powered anode doesn’t need any maintenance nor be changed over time.
Advantages
Powered anode rod advantages & problems solve
Stops Tank Corrosion
Our Corro-Protec anode combined with electrical current will provide added corrosion protection and increase the life of your hot water heater. Our system provides a layer of permanent corrosion protection on the internal welding seams and weak points of the tank. This technology is recognized by corrosion specialists and has been laboratory tested.
24-Hour Sulfur Smell Elimination
No matter what causes the rotten egg smell in your water, the Corro-Protec Powered Anode Rod can solve this problem in just a few hours. Once the system is operational, the energy projected by the system will prevent these unpleasant smells for years to come!
Reduces Limescale Accumulation
Limescale deposits cause significant costs for the rehabilitation of water pipes and heating installations and are also responsible for significant energy losses. The energy sent by the Corro-Protec imposed current anode is used to destabilize the calcium molecule found within the water, which has the effect of preventing the chemical reaction that normally creates calcite.
Automatically Adapts
The Corro-Protec automatically adapts to the type of water present in your tank in order to offer you optimal protection. No matter if your water comes from the city or a well, our products will be able to protect your tank!
One-Time Quick and Easy Installation
This anode will be the last you ever buy. We’ve included step-by-step instructions to make it easier to replace your old water heater hex-head anode with our Corro-Protec with easy-to-follow directions for beginners. If you need help during installation, you can call us or email us.
Lead-Free Certified
Thanks to our special titanium mixed metal oxide rod, the Corro-Protec anode is lead-free and received the gold seal by the Water Quality Association. We are proud to manufacture safe products both for your home and the environment. These Corro-Protec’s anode rods are tested and certified by WQA against SF/ANSI/CAN 372 : 96386, 96387 & 96388.
Standard
Magnesium Anode Rod
Deteriorates over time
The magnesium anode rod will sacrifice itself, deteriorate over time, to protect the water heater.
Anode will corrode
Since corrosion always attacks weaker metals first, the magnesium anode will corrode until it is about 50% consumed. After that, the tank will start to rust and will last a couple years.
Reduces lifespan
Making water more aggressive, water softeners also reduce the life of the sacrificial anode rod.
Corro-Protec
Powered Anode Rod
Stops and prevents corrosion
Using current to stop and prevent corrosion, Corro-Protec relies on an infinite source of energy that will protect your investment for years to come.
No maintenance required
Thanks to laboratory testing over the years, each of our powered anode (impressed current anode) uses current for maximum and permanent protection, and doesn’t require any maintenance even if you also use a water softener.
Fits all water heater models
Our Corro-Protec residential water heater anode rod is specially designed for all models of electric, gas, propane, solar and hybrid water heater tank on the market.
Frequently asked questions
Since the magnesium anode must sacrifice itself to protect the hot water tank, it is important that the anode is large enough to last for several years.
However, since the Corro-Protec anode relies on current to protect the tank instead of sacrificing itself, the rod can be much smaller.
A powered anode is a non-sacrificial anode that uses a current rectifier, plugged into an electrical outlet, which sends current in the hot water tank through a titanium anode.
Unlike sacrificial anodes, powered anodes are maintenance-free and designed to last for years. Plus, they are well known to solve rotten egg odor problems in hot water tanks instead of causing it.
Yes, it is possible to install Corro-Protec by yourself. With all tools needed, it will take you about 15 minutes to install it.
A complete step-by-step guide is included inside the box for an easy installation. Each guide are also available on this page: https://www.corroprotec.com/installation-guide/
Since the amount of current used by the anode will vary from region to region due to the hardness of the water, it is impossible to give an exact answer.
However, on average, the anode will use 10 kWh per year. If we take the average price of electricity in the United States, the cost to run the anode 24 hours a day all year round is $ 1.36 or about a third of a penny per day.
Corrosion is a natural process that happens when two metals or alloys come into contact with each other.
Electrochemical reactions take place at the surface of the metals, and this can cause them to deteriorate and even break down over time. In some cases, corrosion can lead to dangerous situations if not addressed in a timely manner.
There are several ways to prevent corrosion from happening. In your water heater, Corro-Protec’s powered anode rod stops the corrosion process permanently.
We’ve developed different models that can be installed in all water heater brands starting from 10 gallons to 120 gallons, including specific models for Bradford White and Bedarus water heaters. Corro-Protec fits on electric, gas, solar, hybrid, indirect and geothermal water heaters.
To successfully remove your old anode and install your Corro-Protec, certain tools are required. A ratchet wrench fitted with a 1 1/16” socket will be necessary for the removal process. Meanwhile, a socket of 1 3/16” size or an adaptable wrench is recommended for the installation of the Corro-Protec. In addition, a square-headed screwdriver and universal pliers should also be at hand for the operation.
If you have an impact wrench, this could help you remove a stuck sacrificial anode rod.
Need Assistance?
Our technical support team created great step-by-step installation guides. They are also ready to answer all your questions and help you solve any problems you are experiencing.
Blog
Sulfur Smell In Hot Water? Here’s How To Fix It.
Sulfur Smell In Hot Water is a Widespread Issue A common problem many homeowners face is the sulfur smell in hot water. This issue, which […]
Why Your Water Heater is Leaking and How to Fix It
In the US, water leaks in the average home waste 10,000 gallons per year. Worse, 10% of US households have plumbing issues so bad, they waste 32,850 […]
RV Anode Rod
Our RV powered anode rod fits all Suburban RV water heaters. Enjoy the power of our permanent corrosion protection and more.
Commercial Anode Rod
Our commercial anode, powered to, is designed to permanently protect larger water heaters of 90+ gallons. No maintenance required.